Fireplace Freestyle Fiddling #4 It’s Mantle Time

I know this is a long drawn out series – but there’s more components than average to this build, due to the flanking bookcases.

1-checking-the-taperThe tops of the bookcases are slightly sloped intentionally – and because of this the side panel will need to be tapered. First a level is placed on top and the gap is measured for the taper. This is how much we will remove from the bottom to make the top level.

2-trper-jigI use a tapering jig, but you can use a homemade version just as well. This will add a slight taper to our side pieces.

3-squaring-the-sideOnce we have the pieces cut we then need to square the sides to the window casing. I used a framing square and shim out the side piece so everything is now square.

4-tapered-sideA piece is cut for the side top reveal.

5-side-paintedAn additional piece is cut to wrap around the front of the marble top. It is then painted before attaching.

6-mantle-roughNow we’re ready to make the mantle. This is a 5/4 (1″) X 10 clear white pine board. I just set it up to get an idea of the overhang.

7-back-band-cutI decided to make a back-band to go at the back of the mantle. I used a router to add some detail to the top and then cut the three pieces. Here I’m test fitting the cuts.

8-mantle-sides-joinedThe three back-band pieces are glued and nailed together, I then joined the front mantle to the side pieces with a biscuit and glue.

9-mantle-glue-upThe mantle and back band were all assembled as a one piece unit to keep everything flat and straight.

10-test-fit-mantleThen the assembled mantle was test fit into place.

11-painting-back-bandThe back band is finished and a hole was drilled in each side leg of the mantle. I made the side mantle top slightly narrower to make the joint easier to finish and not have to be concerned about the joint separating.

12-mantle-wiringWiring from a wall switch is run under the mantle to both sides of the fireplace for the final test fit.

13-sillite-receptaclesThe wires were for these. Called Sillites, they will allow us to plug in Christmas lights or other decorations on the mantle.

14-attaching-the-mantleOnce the wiring is run we can finally glue and attach the mantle.

15-mantle-in-placeTime to start sanding and finishing.

16-fireplace-side-detailOne more detail is added to the side of pilaster to mirror the design in the sunroom.The paint is BM Ice White in Impervo enamel.

17-shell-detailI’ll sand and paint this a total of four times. I start will 100 grit and finish with 400. It is tedious, but when it’s finally done you can feel the difference.

18-sillite-receptacleThe Sillites have a cover when not in use.

19-finish-paintingSo you think we’d be done – but nooooo – we still have to finish the original details on the bookcases – and slide the fireplace in there.

One more post on this thing and I’m outa here – promise.

 

Advertisements

Fireplace Freestyle Fiddling #2 Design Fail

First I want to thank you for your kind comments – it’s encouraging to hear from some of you who follow along this 6 + year renovation – my,  you sure have long attention spans.

Remember that anyone can do what I do – it’s not difficult if you take your time and be precise in measurement and cutting – or build in some wiggle room in the design like I have on this project. If I hadn’t put in the daddo (groove) in the back of the legs on this fireplace but instead built it on a flat surface – it just would not have worked.  One other thing – be prepared to make changes in the design – especially if you have no clue as to what you plan to do –

See Below

So we left of here.

6-start-of-fireplace-designThe two side legs (pilasters) are removable and the crosspiece is loose. I’ve built small square boxes attached to the front of the pilasters – now we start to figure out our design.

2-fp-designFail # 1 – This seemed like a good idea on paper, but when I glued these on the fireplace I knew I made a mistake. Waffles anyone? I was trying to tie in the design of the cabinet doors.

3-fp-designFail #2 – OK, so maybe if I just move the center element to make a central rectangle and use a simple molding under the mantle.  Nope.

4-fp-designFail #3 – The fluted pilasters are the original pieces that will go on the cabinet frame. So maybe we could make a wider version to fit the pilaster. Still trying to salvage my waffle, I thought maybe I could place a center square of some kind of design. Not feeling it.

5-fp-designSemi Fail #4 – How about making the waffle go away and add a square design element? The flat fluting has got to go away. This thing looks too square.

6-fp-designFail #5 – So let’s put a rounder element in the mix. I had a couple of stair balusters, so why not add these. It will soften the look of all the sharp corners. No, no, no.

7-fp-designGetting warmer – Let’s just get back to basics. I cut some cardboard and mocked up the design elements – we’ll figure out what they are later. I want three elements to mirror the three Ginkgo leaves in the stained glass windows. Also in the photo I’m in the process of adding rock wool insulation up the chimney. This high-heat insulation will help keep the cold out. This is a direct vent fireplace, so the two silver pipes are for venting.

8-fireplace-design-1Fail #6 – My first thought was to use some type of flower to to tie in the leaf theme of the windows. I found a great wood shop out in Oregon that makes stock carvings that I thought I could incorporate. The company is Heartwood Carvings. This was nice, but too far from the arching design the Ginkgo leaves have.

9-fireplace-design-2Fail #7 – We’re getting closer. The palmetto flower had sort of the design I wanted, but I really liked the central scallop shell design.

10-fireplace-final-designI’m tired, my head hurts – let’s just go with this. I found matching scallop shells in a square block and thought that they mirrored the Ginkgo leaf design. My wife was from an island and she eats scallops – so why not?

11-wood-carvingsSo I put in my order and in a few days I got these. Two carved pilasters 4″ X 36″ – Two 5″ square corner blocks and a 5″ X 12″ center block.

12-wood-pilastersTime to get busy and build this thing.

More to come – stick around.